• Latest
  • Trending

Noise and Corrosion

Toray to Boost Polypropylene Film Production to Meet Rising Automotive Capacitor Demand

Toray to Boost Polypropylene Film Production to Meet Rising Automotive Capacitor Demand

Yageo Expects Passive Components Inventory Correction for at Least Two Next Quarters

Yageo Expects Passive Components Inventory Correction for at Least Two Next Quarters

PCNS Passive Components Symposium 11-14th September 2023
Samtec High-Speed Interconnect Enable New Artix and Kintex UltraScale+ SoMs

Samtec High-Speed Interconnect Enable New Artix and Kintex UltraScale+ SoMs

May 2023 ECIA NA Electronic Components Sales Sentiment below April Expectation

May 2023 ECIA NA Electronic Components Sales Sentiment below April Expectation

Paumanok Issues Passive Components in Oil and Gas Electronics Market Outlook 2023-2028

Paumanok Issues Passive Components in Oil and Gas Electronics Market Outlook 2023-2028

Researchers Study Aluminum Dissolution to Increase Supercapacitor Voltages, Suggest New Way of Al Thin Film Deposition

Researchers Study Aluminum Dissolution to Increase Supercapacitor Voltages, Suggest New Way of Al Thin Film Deposition

Frenetic Offers Frenetic Zero One Month Free Magnetic Design Tool

Frenetic Offers Frenetic Zero One Month Free Magnetic Design Tool

Murata Releases 150C Automotive Crystals

Murata Releases 150C Automotive Crystals

KAMIC Group Acquires Wound Components Specialist AGW Electronics

KAMIC Group Acquires Wound Components Specialist AGW Electronics

4th PCNS Registration Opens !

  • Home
  • ABC of CLR
    • All
    • ABC of Capacitors
    • ABC of Inductors
    • ABC of Resistors
    • Mounting Guidelines

    RF Inductors and Filters

    Power transformers

    Telecom transformers

    LAN transformers

    Transformer Calculation and Applications

    Power Inductors 2 (cont.)

    Power inductors

    Current compensated chokes

    Coil with ferrite

    Trending Tags

      • ABC of Capacitors
      • ABC of Inductors
      • ABC of Resistors
      • Mounting Guidelines
    • e-Symposium
    • EPCI Membership
    • About
    No Result
    View All Result
    European Passive Components Institute
    • Home
    • ABC of CLR
      • All
      • ABC of Capacitors
      • ABC of Inductors
      • ABC of Resistors
      • Mounting Guidelines

      RF Inductors and Filters

      Power transformers

      Telecom transformers

      LAN transformers

      Transformer Calculation and Applications

      Power Inductors 2 (cont.)

      Power inductors

      Current compensated chokes

      Coil with ferrite

      Trending Tags

        • ABC of Capacitors
        • ABC of Inductors
        • ABC of Resistors
        • Mounting Guidelines
      • e-Symposium
      • EPCI Membership
      • About
      No Result
      View All Result
      European Passive Components Institute
      No Result
      View All Result
      Home ABC of CLR

      Noise and Corrosion

      January 24, 2022
      Reading Time: 4 mins read
      29 1
      A A

      R 1.9 NOISE

      R 1.9.1 Definition

      Noise manifests itself as a spontaneously fluctuating voltage whose instantaneous amplitude is randomly distributed. The instantaneous value is both unpredictable and of minor interest except in certain critical applications. Instead, one measures a time-averaged value. It consists of the root of the mean-square value of voltage transmitted in a particular frequency pass band.

      The noise consists of two components: Thermal noise and current noise.

      R 1.9.2 Thermal noise voltage

      Thermally agitated charges in the resistance track cause a randomly varying voltage that is called thermal noise. It may be described as the root mean square voltage, E, according to the formula

      ………[R1-11]

      where :

      k is Boltzmann’s constant 1.38 x 10-23 Ws/K

      T is the absolute temperature in Kelvin (K)

      R is the resistance value in ohms

      Δf is the band width of the detector system in Hz.

      From this formula we see that the thermal noise is independent of what kind of resistor type (style) we use.

      R 1.9.3 Current noise voltage

      If we record a DC current through an electrical conductor we would at a sufficiently high amplification be able to see small randomly occurring ripples on the “surface”. They manifest themselves as an increase in mean-square voltage over that caused by thermal noise. The contribution is called current noise or often only noise. It appears above all in materials whose resistance is produced by means of joints between conductive particles embedded in an isolator compound. It is suggestive of the coal granules in the early carbon microphones. In the contact spots current area and conductivity are changed greatly which in turn generates current noise. But also in pure metals in wires and films current noise is generated, although values are negligible in most cases.

      The current noise is approximately direct proportional to applied voltage and inversely proportional to frequency (Figure R1-14).

      Figure R1-14. Examples of current noise in carbon composition resistors.

      Above 10 kHz it usually can be neglected. It grows with the width of the pass band over which it is integrated. It means that the pass band 100…..1000 Hz approximately has the same contents of noise that the pass band 1…..10 kHz. Or in general, every frequency decade has approximately the same noise contents. Suppose the noise contents in a particular defined frequency decade is 1 mV/V. Then the noise for 100 Hz…..10 kHz would be √(12+12) = √2 ≈ 1.4μV/V.

      Since current noise above 10 kHz is often negligible earlier measurements covered the frequency range 200 to 10 kHz.

      According to IEC 195, DIN 44 049, part 1 and MIL-STD-202, method 308, one takes the typical noise characteristic of a frequency decade as one’s starting-point and measures a so called current-noise index expressed either in mV/V or in dB, per frequency decade. One measures geometrically around 1000 Hz, which gives the frequency decade 618 to 1618 Hz. If vrms is the number of mV current noise in an open circuit and VT the applied DC voltage we obtain:

      …..[R1-12]

      In Figure R1-15 we show examples of accounts of noise curves for two different resistor materials. Note how the noise grows with resistance value.

      Current noise can be of great importance in the following cases:

      1. High resistance value.
      2. High DC voltage applied.
      3. Low level circuits and high amplification.
      4. Low or no negative feed back.
      5. Acoustic frequency range.
      6. Linear circuit functions.

      Figure R1-15. Examples of typical current-noise versus resistance in two different resistor materials.

      R 1.10 AQUEOUS CORROSION / ELECTROLYSIS

      Resistance is in principle based on slender conduction paths that are thinner the higher the resistance is. As shown in Figure R1-16 high ohmic resistors become in that way extremely sensitive to electrolytic corrosion.

      Corrosion in its turn implies the presence of moisture. Encapsulation and tight encasing will be decisive in providing environmental resistance of the component. Moreover, if the resistor is loaded with a DC voltage the corrosion velocity increases with voltage until internal heating dries the points of attack.

      Figure R1-16. Schematic of corrosion attacks on low and high resistance elements.


      ABC of CLR: Chapter R Resistors

      Noise and Corrosion

      EPCI licenced content by:

      [1] EPCI European Passive Components Institute experts original articles
      [2] CLR Passive Components Handbook by P-O.Fagerholt*

      *used under EPCI copyright from CTI Corporation, USA

      Creative Commons License
      This page content is licensed under a Creative Commons Attribution-Share Alike 4.0 International License.

      see the previous page:

      Pulse Load, Power and Voltage Derating

      < Page 3 >

      see the next page:

      Voltage and Frequency Dependence

      Previous Post

      Voltage and Frequency Dependence

      Next Post

      Wirewound Resistors – Construction, Pulse Load and Types

      Related Posts

      ABC of CLR

      RF Inductors and Filters

      889
      ABC of CLR

      Power transformers

      727
      ABC of CLR

      Telecom transformers

      569

      Discussion about this post

      Categories

      • ABC of CLR
        • ABC of Capacitors
        • ABC of Inductors
        • ABC of Resistors
        • Mounting Guidelines
      • e-Symposium
        • ESA SPCD
        • PCNS
      • EPCI news
      • news collection

      Popular Posts

      • Transformer: Parasitic parameters and equivalent circuit

        1312 shares
        Share 525 Tweet 328
      • Transformer Calculation and Applications

        691 shares
        Share 276 Tweet 173
      • Introduction to Ceramic Capacitors

        481 shares
        Share 192 Tweet 120
      • Simulation with LTspice

        474 shares
        Share 190 Tweet 119
      • Insulation Resistance, DCL Leakage Current and Voltage Breakdown

        420 shares
        Share 168 Tweet 105

      EPCI Membership

      join passive components community

      © 2023 European Passive Components Institute

      No Result
      View All Result
      • Home
      • ABC of CLR
        • ABC of Capacitors
        • ABC of Inductors
        • ABC of Resistors
        • Mounting Guidelines
      • e-Symposium
      • EPCI Membership
      • About

      Welcome Back!

      Login to your account below

      Forgotten Password?

      Retrieve your password

      Please enter your username or email address to reset your password.

      Log In
      This website uses cookies. By continuing to use this website you are giving consent to cookies being used. Visit our Privacy and Cookie Policy.